Stop Work Authority

Everyone Has the Responsibility to Intervene

Safety Starts With You: If something does not look right, stop, speak up, and address it before work continues.

Stop Work Authority is a clear sign of a strong safety culture. Every employee, regardless of position, experience level, trade, or job title, has both the authority and the responsibility to stop work when a task cannot be performed safely.

This expectation applies to everyone on the jobsite, including apprentices, journeymen, foremen, supervisors, project leadership, and subcontractor partners.

Stopping work is not about slowing production, creating conflict, or questioning someone’s ability. It is about recognizing a concern early, communicating clearly, and preventing an injury before it happens.

 

 

Why Stop Work Authority Matters

Most serious incidents do not happen without warning. In many cases, someone notices a condition that does not seem right before the event occurs. Examples may include missing PPE, an incorrect lockout, damaged equipment, poor weather conditions, an unstable ladder or lift, an energized conductor, incomplete planning, or a change in the work that was not discussed during the Pre-Task Plan.

Employees may hesitate to speak up because they do not want to slow the job down, embarrass a coworker, look inexperienced, or be criticized for raising concern. That hesitation can create real risk.

Speaking up is not a sign of weakness or inexperience. It is a sign of professionalism, leadership, and commitment to the crew.

 

 

When Work Should Stop

Work should stop any time the crew cannot confidently answer this question:

“Can this task be performed safely right now?”

If the answer is no, unclear, or based on assumptions, the task must pause until the concern is resolved.

Examples of Stop-Work Situations
  • Hazards are not identified or controlled in the Pre-Task Plan.
  • Lockout/Tagout requirements are unclear or there is uncertainty about energized equipment.
  • Required PPE is missing, damaged, or incorrect for the task.
  • Ladders, tools, cords, lifts, rigging, or fall protection equipment are damaged or questionable.
  • Guardrails, access points, covers, or leading-edge protections are missing or incomplete.
  • Weather creates additional risks, such as lightning, high winds, snow, ice, or extreme heat.
  • The scope, sequence, location, crew size, or work conditions change from the original plan.
  • Another trade or changing jobsite condition creates an uncontrolled hazard.

 

 

How to Exercise Stop Work Authority

  1. Stop the task safely. Pause the work in a controlled manner and make sure no one continues into the hazard.
  2. Communicate the concern. Notify affected employees and explain what was observed to the foreman, supervisor, or person leading the work.
  3. Reassess the plan. Review the Pre-Task Plan, confirm hazard controls, inspect tools or equipment, and identify what needs to change.
  4. Correct the hazard. Add controls, replace damaged equipment, improve access, verify lockout, adjust manpower, or involve supervision as needed.
  5. Resume only when safe. Work may continue only after the hazard is corrected, the crew understands the revised plan, and affected employees agree the task can be completed safely.

 

 

Leadership Expectations

Supervisors and foremen set the tone for how Stop Work Authority is used in the field. When an employee raises concern, leadership must respond professionally, take the concern seriously, and keep the focus on correcting the hazard.

  • Thank employees for speaking up.
  • Investigate concerns without retaliation, frustration, or embarrassment.
  • Correct hazards promptly and communicate the updated plan.
  • Never pressure employees to continue work they believe is unsafe.
  • If the current plan, tools, equipment, or manpower cannot support safe work, change the plan before continuing.

 

 

Crew Discussion

  • What are some reasons a person might hesitate to stop work?
  • How should coworkers respond when someone raises safety concerns?
  • What hazards on today’s job would justify stopping work immediately?
  • Have we seen a situation where speaking up prevented an incident or near miss?
  • What can we do as a crew to make sure every person feels comfortable using Stop Work Authority?

 

Key Takeaway: Stop Work Authority protects people. A few minutes spent correcting a hazard is always better than explaining why an incident occurred after warning signs were visible.