Electrical Safety

Annual OSHA Refresher Training – November 2026

 

Applicable Standards: OSHA 29 CFR 1926.400 & 1910.332; NFPA 70 (NEC) & NFPA 70E

This refresher covers jobsite electrical hazards, OSHA training requirements for qualified and unqualified workers, NFPA 70E safe work practices, and Encore Electric’s jobsite expectations.

Why This Matters

Electricity is a hidden hazard. You can’t see, smell, or hear it until something goes wrong. NFPA 70 (NEC) and NFPA 70E provide the industry’s best practices for preventing these common construction-site risks:

  • Electric shock from contact with energized parts
  • Arc flash causing severe burns and blast pressure
  • Faulty cords or tools leading to fires or electrocution
  • Improper grounding or damaged GFCIs
  • Improper or unsafe electrical installations
  • Overloaded circuits creating heat and ignition sources

1. Know Your Training Requirements (OSHA 1910.332)

Employees must be trained based on whether they are qualified or unqualified:

Qualified Workers Unqualified Workers
Permitted to work on or near exposed energized parts. Must understand:

·        Lockout/Tagout procedures

·        Approach boundaries (arc flash, limited, and restricted)

·        Voltage testing and verification of de-energization

·        Arc flash PPE and hazard categories

·        Safe work practices for energized and de-energized systems

Not authorized to work on energized parts. Must know:

·        Electrical hazard recognition

·        Safe distances from exposed conductors

·        Cord and tool inspection

·        GFCI use on construction sites

·        Reporting hazards immediately

2. Follow Key Safety Practices (NFPA 70E & OSHA)

  • De-energize whenever possible. Energized work requires justification, a permit, and appropriate PPE.
  • Use lockout/tagout before servicing equipment.
  • Inspect cords, plugs, and tools before each use.
  • Maintain clear access to panels, disconnects, and breakers per NEC requirements.
  • Never bypass GFCIs or use damaged extension cords.
  • Keep electrical equipment dry and avoid wet conditions unless equipment is rated for them.
  • Wear appropriate PPE for the task and hazard category.
  • Follow approach boundaries. Unqualified workers must stay outside the Arc Flash Boundary.

3. Jobsite Expectations

These expectations apply to every Encore Electric job site, without exception:

  • Stay alert around energized equipment.
  • Every electrical conductor, circuit part, or device is to be considered energized until proven otherwise. If You Can Touch It, Test It!
  • If a branch circuit or associated circuit parts are found to be energized, stop work immediately and contact an appropriate supervisor.
  • Every single Electrician and Technology Solutions team member must carry the approved FLUKE 2AC proximity tester.
  • Follow your Job Site Specific LOTO policy.
  • A meter check must be performed and documented weekly.

 

Stop-Work Conditions

Immediately use your Stop work Obligation and contact your supervisor when:

  • A branch circuit or associated circuit parts are found to be energized.
  • Damaged cords, damaged GFCIs, or exposed wiring are found.
  • Your proximity tester or voltmeter has not been checked or fails the meter check.
  • LOTO cannot be applied as required by the Job Site Specific LOTO policy.
  • You do not have the PPE required for the task and hazard category.
  • Anyone is unsure whether equipment is de-energized.

When in doubt: STOP, TEST, and ASK.

Crew Discussion

Every employee must be able to answer:

  • What electrical hazards exist on this site?
  • What equipment is energized?
  • What PPE is required for my task?
  • Where are the disconnects and breakers?
  • What do I do if I find damaged cords or exposed wiring?
  • Who is the person in charge, and who is the authorized employee(s) for LOTO on this job site?
  • What is everyone’s role as part of the LOTO Program?

If any of these answers are unclear, training must be reinforced immediately.

Key Takeaway

  • OSHA requires electrical safety training based on job assignment.
  • Refer to Encore Electric’s Zero-Volt Verification procedures and Encore’s Electrical Safety Program.
  • Follow all safety policies and procedures and use safe work practices to prevent shock, arc flash, and other injuries from electrical contact.
  • Most electrical incidents are preventable with proper training, hazard recognition, and mitigation.
  • Do it SAFE, Do it Right, Ask questions if unsure.
  • We want the Best Trained, Best Equipped, and SAFEST Electricians at ENCORE Electric.

OSHA Quick Reference

Topic Reference
Electrical safety in construction 29 CFR 1926.400
Electrical safety-related work practices training 29 CFR 1910.332
Installation requirements (clear access, grounding, GFCIs) NFPA 70 (NEC)
Approach boundaries, energized work permits, arc flash PPE NFPA 70E
Zero voltage verification and LOTO Encore Electric Zero-Volt Verification procedures, Encore Electric Electrical Safety Program, and Job Site Specific LOTO policy