Process Safety Management (PSM)
Annual OSHA Refresher Training
OSHA Standards: 29 CFR 1910.119 and 29 CFR 1926.64
Understanding Process Safety Management (PSM) and Preventing Catastrophic Releases of Hazardous Chemicals
Purpose
PSM applies only when a process contains a highly hazardous chemical at or above the threshold quantity listed in 29 CFR 1910.119 Appendix A or contains 10,000 pounds or more of a Category 1 flammable gas or a flammable liquid with a flashpoint below 100°F, subject to the exemptions in 29 CFR 1910.119(a). Site-specific training must identify whether employees work in or near a PSM-covered process and explain the hazards and safeguards that apply to that process.
Process Safety Management (PSM) is designed to prevent or minimize the consequences of catastrophic releases of toxic, reactive, flammable, or explosive chemicals. These incidents can result in serious injuries, fatalities, environmental damage, and significant property loss.
By the end of this refresher, employees should be able to identify the PSM-covered processes and highly hazardous chemicals relevant to their work; locate applicable process safety information and operating procedures; recognize process deviations and warning signs; explain management-of-change, permit, and pre-startup requirements; describe required emergency actions; and identify how to report hazards, near misses, releases, and process safety concerns.
Common Process Safety Hazards
- Flammable liquids and gases
- Toxic chemicals
- Reactive substances
- High-pressure systems
- High-temperature processes
- Chemical storage and transfer operations
- Equipment failures
- Unauthorized process changes
Examples include:
- Ammonia refrigeration systems
- Petroleum refining operations
- Chemical manufacturing
- Bulk fuel storage facilities
- Industrial gas processing systems
Key Elements of PSM
1. Employee Participation
- Participate in safety meetings and hazard reviews.
- Report unsafe conditions immediately.
- Contribute ideas for safer operations.
2. Process Safety Information
Know:
- Chemical hazards
- Safe operating limits
- Process flow information
- Equipment design information
A process hazard analysis must identify, evaluate, and control the hazards of each PSM-covered process using an appropriate methodology, such as a What-If analysis, checklist, HAZOP, failure mode and effects analysis, fault tree analysis, or another suitable method. The analysis must address previous incidents with potentially catastrophic consequences, engineering and administrative controls, consequences of control failures, human factors, and possible safety and health effects on employees. The analysis must be revalidated at least every five years. See 29 CFR 1910.119(e).
3. Operating Procedures
Always:
- Follow written procedures.
- Never bypass established processes.
- Use approved startup, shutdown, and emergency procedures.
4. Training
Employees involved in operating a PSM-covered process must receive initial training on the process, operating procedures, specific safety and health hazards, emergency operations, safe work practices, and other practices necessary to perform their assigned duties safely. Refresher training must be provided at least every three years, and more often, when necessary, in consultation with employees involved in operating the process. This annual refresher supports the company’s more frequent training schedule and does not replace required initial, task-specific, or change-related training. The employer must document the employee’s identity, training date, and the means used to verify that the employee understood the training. See 29 CFR 1910.119(g).
- Understand process hazards.
- Perform assigned tasks safely.
- Respond appropriately during emergencies.
5. Mechanical Integrity
Ensure:
- Equipment inspections are completed.
- Preventive maintenance is performed.
- Defective equipment is repaired promptly.
6. Management of Change (MOC)
Before changing:
- Equipment
- Chemicals
- Procedures
- Technology
Ensure the change is reviewed, documented, and approved.
The complete PSM program also includes process hazard analysis, contractor management, pre-startup safety review, hot work permits, incident investigation, emergency planning and response, compliance audits, and protection of trade secrets. Employees must understand how these elements apply to their work, including their responsibility to follow approved safeguards, support hazard reviews and investigations, comply with permit requirements, and report incidents and near misses. Applicable citations are 29 CFR 1910.119(e), (h), (i), (k), (m), (n), (o), and (p).
Before the covered process is started after a significant new installation or modification, the employer must confirm that construction and equipment meet design specifications, safety and operating procedures are in place, the process hazard analysis and management-of-change requirements have been addressed, and affected employees have been trained. Employees whose duties are affected by a management-of-change decision must be informed of and trained on the change before startup. See 29 CFR 1910.119(i) and 29 CFR 1910.119(l).
Warning Signs of a Potential Process Safety Incident
Watch for:
- Leaking valves, pipes, or hoses
- Corrosion or damaged equipment
- Unusual odors
- Pressure fluctuations
- Unexpected process alarms
- Excessive vibration
- Unauthorized modifications
- Bypassed safety devices
If you see something, say something immediately.
Employee Responsibilities
Every worker should:
- Follow operating procedures
- Attend required training
- Wear required PPE
- Report near misses and hazards
- Participate in emergency drills
- Never bypass safety systems
- Stop work when unsafe conditions exist
Emergency Response Actions
If a chemical release, fire, explosion, or other process emergency occurs, follow the site-specific emergency action or emergency response plan. Employees who are not trained and authorized responders must immediately report the emergency, activate alarms as directed, evacuate to the designated assembly area, and remain available for accountability. Do not enter or re-enter the affected area or attempt spill control, rescue, or other emergency response unless specifically trained, equipped, and authorized. Emergency planning and response must comply with 29 CFR 1910.119(n) and the applicable requirements of 29 CFR 1910.38 and 29 CFR 1910.120(q).
- Follow site emergency procedures.
- Notify supervision immediately.
- Activate alarms if required.
- Evacuate to designated assembly areas.
- Do not attempt emergency response unless trained and authorized.
- Account for all personnel.
Discussion Questions
- What chemicals or processes at our site are covered by PSM?
- How do we report safety concerns?
- What should you do if you discover a leaking valve or pipe?
- Why is Management of Change important?
- What emergency actions should be taken during a chemical release?
Please reach out to the Safety Department if you have any questions or need further assistance identifying PSM-covered processes, chemicals, or hazards.